View MSK640B_1284466.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ISO 9001 CERTIFIED BY DSCC
M.S.KENNEDY CORP. FEATURES:
WIDE BANDWIDTH, HIGH VOLTAGE CRT VIDEO AMPLIFIER
640
(315) 701-6751
4707 Dey Road Liverpool, N.Y. 13088 Pin Compatible with LH2424 and CR2424 High-Rel Versions 2nS Transition Times Drives 8.5pF Capacitive Load With Ease DC Coupled for Output Level Adjust 175MHz Bandwidth 55Vpp Output Swing
MIL-PRF-38534 CERTIFIED
DESCRIPTION:
The MSK 640(B) is a wide bandwidth, high voltage color or monochrome CRT video amplifier designed specifically to drive the cathode of today's most demanding high resolution CRT monitors. The MSK 640(B) is a transimpedance amplifier capable of achieving a 25V output voltage swing with an input current of 9.3mA. The output of the amplifier is DC biased at half the power supply voltage. Transition times in the range of 2nS enable the MSK 640 to drive 10nS pixels with ease and make it ideally suited for monitors with 1280 x 1024 or higher display resolutions. The 9 pin single in-line bathtub package is pin for pin compatible with the LH2424 and CR2424 and is a drop in replacement for the high-rel versions of these devices with improved stability and thermal performance.
EQUIVALENT SCHEMATIC
TYPICAL APPLICATIONS
CRT Driver for Color and Monochrome Monitors High Voltage Transimpedance Amplifier Ultra High Speed Amplifier for Test Equipment
1
PIN-OUT INFORMATION
1 2 3 4 5 Inverting Input Ground Ground Vcc Vcc 6 7 8 9 Vcc Ground Ground Output
Rev. B 8/00
ABSOLUTE MAXIMUM RATINGS

ELECTRICAL SPECIFICATIONS
Parameter STATIC Power Supply Current VIN=N/C 1 2 3 Input Bias Voltage Output Offset Voltage Input Capacitance 2 Power Supply Range DYNAMIC CHARACTERISTICS Output Voltage High Output Voltage Low Voltage Gain Rise Time Fall Time Overshoot (Adjustable) 2 -3dB Bandwidth Linearity Error
2
+Vcc=+60V Unless Otherwise Specified
Group A Subgroup Min. 1.4 1.35 28 26 40 55 10.5 130 MSK 640B Typ. 40 55 35 1.55 30 30 10 60 58 2 12.5 2.1 2 25 175 0.5 Max. 45 65 45 1.7 1.8 32 34 75 5 14.5 2.9 2.9 1.5 5 Min. 1.3 27 40 55 10 125 MSK 640 Typ. 40 55 35 1.55 30 10 60 58 2 12.5 2.1 2 25 175 0.5 Max. 50 1.8 33 70 5 15 3 3 1.5 5
Test Conditions 1
VIN=N/C VIN=N/C VIN=0.7V Derated Performance f=10KHz f=10KHz VIN=2VPP; f=10KHz VOUT=40VPP VOUT=40VPP VOUT=20VPP VOUT=20VPP f=1KHz f=10KHz; 5VPPVOUT50Vpp
1 2,3 1 2,3 4 4 4 4 4 4
Low Frequency Tilt Voltage 2
NOTES:
1 2 3 4 5 6 RIN=215, CIN=100pF, CLOAD=8.5pF, RL=, unless otherwise specified (See Figure 1). Guaranteed by design but not tested. Typical parameters are representative of actual device performance but are for reference only. Industrial grade devices shall be tested to subgroups 1 and 4 unless otherwise specified. Military grade devices ('B' suffix) shall be 100% tested to subgroups 1,2,3 and 4. Subgroup 5 and 6 testing available upon request. Subgroup 1,4 TA=TC=+25C Subgroup 2,5 TA=TC=+125C Subgroup 3,6 TA=TC=-55C
2
Rev. B 8/00

TJ

IOUT
250mA
TC

+VCC JC
Supply Voltage Thermal Resistance (Junction to Case) Peak Output Current
+75V 10.5C/W
TST TLD
Storage Temperature Range -65C to +150C Lead Temperature Range 300C (10 Seconds) Case Operating Temperature MSK640 -40C to +85C MSK640B -55C to +125C Junction Temperature 175C
Units
mA mA mA V V V V pF V V V V/V nS nS % MHz V %
APPLICATION NOTES TYPICAL TEST CIRCUIT
The signal source in Figure 1 can be either a fast pulse generator or a network analyzer as long as the output impedance is 50 ohms. The DC level of the input should be 1.55V and all cables should be kept as short as possible. Since total load capacitance should be kept below 8.5pF, a FET probe should be used on the ouput.
OUTPUT ISSUES
The output of the MSK 640 is a pair of bipolar emitter followers configured in a complimentary push pull configuration. This configuration eliminates the need for a pull up load resistor and makes the amplifier less susceptible to load capacitance variations. Connecting a wire or cable from the output of the amplifier to the CRT cathode can create a resonant circuit which can cause unwanted oscillations or overshoot at its resonant frequency. A damping resistor in series with the lead inductance will alleviate this condition. The optimum value of this resistor can be determined using the following formula: R = 2* L/C This resistor also doubles as an arcing protector. In the breadboarding stage, the value of this resistor should be determined experimentally. Resistance in the range of 50 to 100 ohms is usually sufficient. If a quick, simple peaking network is desired, a 300 ohm cable terminated by a capacitor will act like an inductor in the frequency range involved.
USING THE MSK 640
The output of the amplifier is biased at one half of the power supply voltage. An output voltage swing of 25 volts is typical with a power supply voltage of +60 volts. With an 8.5pF capacitive load, transistion times are in the 2.1nS range. If a spark gap current limiting resistor is used on the output of the amplifier and the transistion times are degraded, a peaking coil may be used to preserve system performance. The optimum value for this coil will be in the range of 100 to 200nH and can best be determined by trial and error. The output of the MSK 640 is not short circuit protected, therefore, purely resistive loads should be no less than 600 ohms at any time to avoid damaging the output.
TRANSIMPEDANCE AMPLIFICATION
Transimpedance amplifiers relate input current to output voltage. The MSK 640 contains an internal 3K feedback resistor. This resistor converts input current to output voltage in the following manner (See figure 1): 1.43V (referenced to 1.55Vdc) across the 215 input resistor results in an input current of 6.65mA. This current flows through the 3K feedback resistor and results approximately in a 20V swing at the output. The actual voltage gain of the typical MSK640 circuit may be slightly less due to transistor losses. The following formula approximates voltage gain including potential losses: Voltage Gain (V/V) = 3K/(Rin + L) L 25
OPERATION CONSIDERATIONS
The input of the MSK 640 rests at a +1.55VDC level with the input terminal open. In this state, the output rests at one half of the power supply voltage. When connecting a pulse generator to the input of the amplifier, the DC level should be offset so that the signal is centered around +1.55V. During characterization, the input should be coupled to the MSK 640 through a parallel combination of a variable resistor and variable capacitor peaking circuit. Optimum values for the peaking circuit can be determined experimentally. The optimum value of load capacitance is 8.5pF. Viewing the output with a normal oscilloscope probe would seriously degrade performance. A FET probe fitted with a 100:1 voltage divider will add only approximately 1.5pF of capacitance to the load and is highly recommended. An experimental circuit along with recommended values can be found in Figure 2.
HEAT SINKING
The MSK 640 requires heat sinking in most applications. The following formula may be applied to determine if a heat sink is necessary and what size and type to use. Rsa = ((Tj-Ta)/Pd ) - (Rjc) - (Rcs) WHERE Tj = Junction Temperature Pd = Total power dissipation Rjc = Junction to case thermal resistance Rcs = Case to heat sink thermal resistance Rsa = Heat sink to ambient thermal resistance Tc = Case temperature Ta = Ambient temperature Ts = Sink temperature EXAMPLE Tj = 150C Ta = 100C Pd = 3W Rjc = 10.5C/W Rcs = 0.15C/W Solving the above equation for Rsa (heat sink thermal conductivity) shows that the heat sink for this application must have a thermal resistance of no more than 6.0C/W to maintain a junction temperature of no more than 150C. 3 Rev. B 8/00
TYPICAL PERFORMANCE CURVES
4
Rev. B 8/00
COMPLETE VIDEO SYSTEM
Figure 3 above shows how an MSK 620 and MSK 640 can be used to drive a 100MHz monochrome monitor. The video signal is A.C. coupled through C1. The video output pin of the MSK 620 rests at approximately +3.9Vdc and the input of the MSK 640 should be D.C. biased at approximately +1.55Vdc. D1, D2, D3 and Q1 act as a level shifting stage to match the output of the MSK620 and the input of the MSK640. R8 and R9 sample the output and feed it back to the clamping section of the MSK 620 for black level control superior to simply sampling from pin 14 of the MSK 620. 5 Rev. B 8/00
MECHANICAL SPECIFICATIONS
NOTE: ESD Triangle indicates Pin 1. ALL DIMENSIONS ARE 0.010 INCHES UNLESS OTHERWISE LABELED
ORDERING INFORMATION
Part Number MSK640 MSK640B Screening Level Industrial Military-Mil-PRF-38534
4707 Dey Road, Liverpool, New York 13088 Phone (315) 701-6751 FAX (315) 701-6752 www.mskennedy.com
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make changes to its products or specifications without notice, however, and assumes no liability for the use of its products.
M.S. Kennedy Corp.
6
Rev. B 8/00

▲Up To Search▲

Price & Availability of MSK640B

	To Download MSK640B Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .